TD62107PG/fg 2007-11-30 1 toshiba bipolar digital integrat ed circuit silicon monolithic TD62107PG,td62107fg 4ch high-current dar lington sink driver the TD62107PG/fg are high-voltage, high-current darlington drivers and enable inputs which ca n gate the outputs. all units feature integral clamp diodes for switching inductive loads. the TD62107PG/fg have a wide supply voltage range and all input are compatible with ttl and 5-v cmos. application include relay, hammer, lamp and stepping moter drivers. please observe the thermal condition for using. the suffix (g) appended to th e part number represents a rohs-compatible product. features ? output current (single output) 750 ma (max) ? high sustaining voltage output: 45 v min (TD62107PG) 35 v min (td62107fg) ? output clamp diodes ? enable inputs e1, e2 ? wide supply voltage range v cc = 4.75 to 7 v ? input compatible with ttl and 5-v cmos ? gnd terminal = heat sink ? package type-pg: dip-16pin ? package type-fg: hsop-16pin pin assignment (top view) TD62107PG td62107fg TD62107PG td62107fg weight dip16-p-300-2.54a: 1.11 g (typ.) hsop16-p-300-1.00: 0.50 g (typ.) heat sink & gnd 1 2 3 4 5 6 7 14 13 12 11 10 9 o2 heat sink & gnd o3 o4 com v cc e1 i1 i2 i3 i4 16 2e 8 15 o1 heat sink & gnd 1 2 3 4 5 6 7 14 13 12 11 10 9 nc heat sink & gnd o4 com nc v cc e1 i1 nc i3 nc 16 2 e 8 15 o1 o3 o2 i2 i4
TD62107PG/fg 2007-11-30 2 schematics (each driver) truth table e1 2 e i1 to i4 o1 to o4 l l l or h disable off l h l or h disable off h l l or h enable in h h l or h disable off in = i1 to i4 input equivalent circuit ou tput equivalent circuit note: the input and output parasitic diod es cannot be used as clamp diodes. absolute maximum ratings (ta = 25c) characteristics symbol rating unit supply voltage v cc ? 0.5 to 17 v pg ? 0.5 to 45 output sustaining voltage fg v ce (sus) ? 0.5 to 35 v output current i out 750 ma input voltage v in ? 0.5 to v cc + 0.5 v pg 45 clamp diode reverse voltage fg v r 35 v clamp diode forword current i f 500 ma pg 2.7 (note 1) power dissipation fg p d 1.4 (note 2) w operating temperature t opr ? 40 to 85 c storage temperature t stg ? 55 to 150 c note 1: on glass epoxy pcb (50 50 1.6 mm cu 50%) note 2: on glass epoxy pcb (60 30 1.6 mm cu 30%) common output v cc input i1 i2 i3 i4 o1 o2 o3 o4 common e1 2e
TD62107PG/fg 2007-11-30 3 operating conditions (ta = ? 40 to 85c) characteristics symbol test condition min typ. max unit supply voltage v cc ? 4.75 ? 15 v pg 0 ? 45 output sustaining voltage fg v ce (sus) ? 0 ? 35 v t pw = 25 ms, duty = 75%, 1 circuit 0 ? 500 pg duty = 30% 0 ? 400 output current fg i out t pw = 25 ms, 4 circuit duty = 40% ? ? 300 ma input voltage v in ? 0 ? v cc v pg ? ? 45 clamp diode reverse voltage fg v r ? ? ? 35 v clamp diode forward current i f ? ? ? 500 ma pg ? ? ? 1.0 power dissipation fg p d ta = 85c (note 1) ? ? 0.7 w note1: on glass epoxy pcb (60 30 1.6 mm cu 30%) electrical characteristics (ta = 25c) characteristics symbol test circuit test condition min typ. max unit high level v ih 2.0 ? v cc input voltage low level v il 1 ? ? 0.8 v pg v ce = 45 v, ta = 75c ? ? 100 output current high level fg i oh 2 v ce = 35 v, ta = 85c ? ? 100 a i out = 50 ma ? ? 1.3 output voltage low level v ol 3 i out = 750 ma ? ? 1.6 v high level i ih 4 v in = 13 v ? ? 100 a input current low level i il 5 v in = 0.4 v ? ? ? 0.3 ma pg v r = 45 v ? ? 100 clamp diode reverse current fg i r 6 v r = 35 v ? ? 100 a clamp diode forward voltage v f 7 i f = 500 ma ? ? 2.0 v output high i cch 4 v cc = 13 v, v in = 0 v output open ? ? 13 supply current output low i cc i ccl 5 v cc = 13 v, v in = 5 v output open ? ? 17 ma pg v cc = 5 v, r l = 90 c l = 15 pf, v out = 45 v ? 5 ? turn-on delay fg t on 8 v cc = 5 v, r l = 70 c l = 15 pf, v out = 35 v ? 5 ? s pg v cc = 5 v, r l = 90 c l = 15 pf, v out = 45 v ? 5 ? turn-off delay fg t off 8 v cc = 5 v, r l = 70 c l = 15 pf, v out = 35 v ? 5 ? s
TD62107PG/fg 2007-11-30 4 test circuit 1. v ih , v il 2. i oh 3. v ol 4. i ih , i ccl 5. iil, i ccl 6. i r 7. v f 8. t on , t off input condition note 1: pulse width 50 s, duty cycle 10% output impedance 50 , t r 5ns, t f 10 ns note 2: v ih = 3 v, e1 = v ih , 2e = gnd, v cc = 5 v note 3: c l includes probe and jig capacitance precautions for using this ic does not include built-in protection circuits for excess current or overvoltage. if this ic is subjected to excess current or overvoltage, it may be destroyed. hence, the utmost care must be taken when systems which incorporate this ic are designed. utmost care is necessary in th e design of the output line, v cc , common and gnd line since ic may be destroyed due to short-circuit between outputs, air co ntamination fault, or fault by improper grounding. pulse generator (note 1) input c l = 15 pf (note 3) v out output r l open v cc = 5 v (note 2) v in (on) v ol open i out v cc i ccl i ih v in open open v cc i cch i il v in open open v cc open open i r v r v cc open open i f v f v cc 10% 50% t on t off t f t r v ih = 3 v v oh v ol input 50% 50 s output 50% 50% 90% 10% 90% 0 i oh open v ce v cc v ih , v il v ce open v cc i out
TD62107PG/fg 2007-11-30 5 0 0 75 150 4.0 3.0 1.0 2.0 100 25 125 50 TD62107PG v ce (sat) ? i out v out ? v in i out ? duty cycle i out ? duty cycle p d ? ta p d ? ta output saturation voltage v ce (sat) (v) input voltage v in (v) duty cycle (%) duty cycle (%) ambient temperature ta (c) ambient temperature ta (c) output current i out (a) output current i out (a) i out (a) output current i out (a) power dissipation p d (w) power dissipation p d (w) 0 0 75 150 4 3 1 2 100 25 125 50 (1) type-fg on pcb 60 30 1.6 mm cu 30% (2) type-fg free air (1) (2) 0 0 1.2 1.6 8.0 6.0 0.2 0.4 0.4 0.8 v cc = 5 to 17 v ta = 75c ? 30 25 0 0 4.0 5.0 50 20 30 2.0 3.0 ? 30 25 ta = 75c i out = 500 ma 40 10 1.0 0.2 30 90 0.8 0.4 0.6 50 70 ta = 75c recommended limit 4 circuit 2 1 3 device limit 0.2 30 90 0.8 0.4 0.6 50 70 ta = 25c 4 circuit 3 1, 2 device limit recommended limit
TD62107PG/fg 2007-11-30 6 package dimensions weight: 1.11 g (typ.)
TD62107PG/fg 2007-11-30 7 package dimensions weight: 0.50 g (typ.)
TD62107PG/fg 2007-11-30 8 restrictions on product use ? toshiba corporation, and its subsidiaries and affiliates (collect ively ?toshiba?), reserve the right to make changes to the in formation in this document, and related hardware, software an d systems (collectively ?product?) without notice. ? this document and any information herein may not be reproduc ed without prior written permission from toshiba. even with toshiba?s written permission, reproduc tion is permissible only if reproducti on is without alteration/omission. ? though toshiba works continually to improve product?s quality a nd reliability, product can malfunction or fail. customers are responsible for complying with safety standards and for prov iding adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situat ions in which a malfunction or failure of product could cause loss of human life, b odily injury or damage to property, including data loss or corruption. before creating and producing des igns and using, customers mus t also refer to and comply with (a) the latest versions of all re levant toshiba information, including without limitation, this d ocument, the specifications, the data sheets and applic ation notes for product and the precautions and conditions set forth in the ?tosh iba semiconductor reliability h andbook? and (b) the instructions for the applicati on that product will be used with or for. custome rs are solely responsible for all aspects of t heir own product design or applications, incl uding but not limited to (a) determining th e appropriateness of the use of this product in such design or applications; (b) evaluating and det ermining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. toshiba assumes no liability for customers? product design or applications. ? product is intended for use in general el ectronics applications (e.g., computers, personal equipment, office equipment, measur ing equipment, industrial robots and home electroni cs appliances) or for specif ic applications as expre ssly stated in this document . product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality a nd/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or se rious public impact (?unintended use?). unintended use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic s ignaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to el ectric power, and equipment used in finance-related fields. do not use product for unintended use unless specifically permitted in thi s document. ? do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy product, whether in whole or in part. ? product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. ? the information contained herein is presented only as guidance for product use. no re sponsibility is assumed by toshiba for an y infringement of patents or any other intellectual property rights of third parties that may result from the use of product. no license to any intellectual property right is granted by this documen t, whether express or implied, by estoppel or otherwise. ? absent a written signed agreement, except as provid ed in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, toshiba (1) assumes no liability whatsoever, including without limitation, indirect, co nsequential, special, or incidental damages or loss, including without limitation, loss of profit s, loss of opportunities, business interruption and loss of data, and (2) disclaims any and all express or implied warranties and conditions related to sale, use of product, or information, including warranties or conditions of merchantability, fitness for a particular purpose, accuracy of information, or noninfringement. ? do not use or otherwise make available product or related soft ware or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical , or biological weapons or missi le technology products (mass destruction w eapons). product and related software and technology may be controlled under the japanese foreign exchange and foreign trade law and the u.s. expor t administration regulations. ex port and re-export of product or related software or technology are strictly prohibited exc ept in compliance with all applicable export laws and regulations. ? please contact your toshiba sales representative for details as to environmental matters such as the rohs compatibility of pro duct. please use product in compliance with all applicable laws and regula tions that regulate the inclusion or use of controlled subs tances, including without limitation, the eu rohs directive. toshiba assumes no liability for damages or losses occurring as a result o f noncompliance with applicable laws and regulations.
|
